fzk011-mechanischer-thermostat-mechanical-thermostat-feature

Mechanical thermostat

FZK 011

The set value corresponds to the upper switching point, here the contact breaker opens. The set value minus the switching temperature differential of 5 K (and tolerances) corresponds to the lower switching point, here the contact breaker closes. The mechanical thermostat is used to control heating, cooling devices, filter fans or signal transmitters.

Adjustable temperature
Small hysteresis enables precise control
High switching capacity
Change-over contact (heating or cooling)
Clip fixing

Overview technical data

Device type	Thermostats
Contact type	Snap-action contact
Sensor	Thermostatic bimetal
Protection type	IP20
Casing	Plastic to UL94 V-0, light grey
AC/DC	AC
Inrush current maximum	16 A
Inrush current duration	10 s
Switching capacity	Normally closed: AC 10 (4) A, DC 30 W Normally open: AC 5 (2) A, DC 30 W
Switching current ohmic	10 A(NC)
Switching current 2 ohmic	5 A(NO)
Reference voltage ohmic maximum	250 VAC
Reference voltage 2 ohmic maximum	120 VAC
Switching current inductive	4 A(NC)
Switching current 2 inductive	2 A(NO)
Reference voltage inductive maximum	250 VAC
Reference voltage 2 maximum	120 VAC
Switching current dc ohmic	1 A
Reference voltage dc ohmic maximum	30 VDC
Minimal switching capacity	0,48 W
Reference voltage minimum	24 V
Switching current	10 mA
Service life	>100000 cycles
Switching differential	5 K
Switching differential tolerance	-3/+2 K
Operating temperature	-45 °C - 65 °C
Operating humidity	≤90 % RH
Storage humidity	≤90 % RH
Storage temperature	-45 °C - 65 °C
Torque	0,5 Nmmax.
Connection	4-pole clamp, torque 0.5 Nm max: Rigid wire/stranded wire² 2.5 mm² (AWG 14)
Design	Change-over contact
Mounting	Clip for 35 mm DIN rail, EN 60715
Height	67 mm
Width	50 mm
Depth	38 mm
Weight	100 g
Note	The controller's contact system is exposed to environmental influences, which can change the contact resistance. This can lead to a voltage drop and/or self-heating of the contacts. During usage of the NC (normally closed) contact, there is the possibility of thermal return to reduce the switching temperature differential by connecting the clamp "N" (RF heating resistor). It depends on the ambient conditions and must be determined in tests for the respective application. Wire end ferrules must be used for connections with stranded wires.

Product variants

Article number	Follow-up article	Setting range	Operating voltage minimum	Operating voltage tolerance maximum	Datasheet
01170.0-00	01179.0-00	5 °C - 60 °C	230 V	250 V	FZK011-01170.0-00-Datasheet-EN-SE.pdf
01170.0-02		-20 °C - 35 °C	230 V	250 V	FZK011-01170.0-02-Datasheet-EN-SE.pdf
01170.9-00		40 °F - 140 °F	120 V	120 V	FZK011-01170.9-00-Datasheet-EN-SE.pdf
01170.0-01		40 °F - 140 °F	230 V	250 V	FZK011-01170.0-01-Datasheet-EN-SE.pdf
01170.9-01		5 °C - 60 °C	120 V	120 V	FZK011-01170.9-01-Datasheet-EN-SE.pdf

Mechanical thermostat

FZK 011

Overview technical data

Product variants

Certificates

Your direct contact

Stego Worldwide